SAE J This standard provides a system of a defined nomenclature to describe vehicle dimensions. A. combination of letters and numerals helps the. This SAE Recommended Practice defines a set of measurements and standard procedures for motor vehicle dimensions. The dimensions are primarily intended . 26 May BY ORDER OF THE EXECUTIVE DIRECTOROffice of the Federal RegisterWashington, Authority of the Code of Federal Regulations.

Author: Vudozil Yozshuhn
Country: Austria
Language: English (Spanish)
Genre: Video
Published (Last): 2 May 2012
Pages: 42
PDF File Size: 10.56 Mb
ePub File Size: 3.81 Mb
ISBN: 651-9-22085-914-2
Downloads: 48325
Price: Free* [*Free Regsitration Required]
Uploader: Tygojas

When sae j1100 best load is obtained using the Standard Luggage Set, H-boxes may be added to arrive at the final load. If there is no second step, the dimension will be to the top of the sill plate bead at the center of the sae j1100 door opening.

sae j1100 The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any sae j1100 infringement arising therefrom, sae j1100 the sole responsibility of the user. In case of dual rear axles, the dimension shall be to the midpoint ssae the centerlines of the rear wheels.

For rear-facing third seat, measure from the sae j1100 seat back at a height tangent to the top of the third Seat Cushion surface, rearward to the interior tailgate closure. L11 Accelerator heel point to steering wheel center X 6. If the mirror is located on the instrument panel, the dimension will be measured from the top of the mirror frame in the highest usable position sad the bottom of SAE 95th percentile eyellipse.

SAE J1100: Motor Vehicle Dimensions

Sxe SgRP – front – Z coordinate 6. W16 Cushion width – front 6. The Luggage Compartment Lid or access door must close and lock freely without forcing or excessive slamming with all of the luggage in place in the compartment. Four-Door Models — Same as L1 8 b. Search the history of over billion web pages on the Internet. This measurement includes vertical adjustment independent sae j1100 track sae j1100 rise.


In case of dual 1j100, the dimension will be measured to the centerline of tire and wheel assemblies. Application— This SAE Recommended Practice defines a uniform set of interior and exterior dimensions for passenger cars, multipurpose passenger vehicles, and sae j1100. If there is a sae j1100, the dimension is measured sae j1100 from the ground to the first step entering the vehicle. This surface is the rearmost point of driver’s seat on trucks with closed cargo area sse is the front surface of the inside of cargo swe on trucks with open cargo area.

W width and H height codes to denote specific pedal dimensions. Definition Revised Section No. Each dimension is assigned a code which is composed of a prefix sae j1100 denoting the direction or type of dimension and a number issued in sequence as required by each prefix letter. The dimension shall be at height of the cargo floor surface, if floor surface at engine cover is above cargo floor surface, then length is taken at floor to engine cover intersection height.

These Vehicle K1100 are established to enable uniform static comparisons of dimensions affected by the ground plane and vehicle pitch attitude.

Foremost-Highest Design H-Point— The foremost location sae j1100 the full up position of vertical travel sae j1100 of track rise.

This is a negative dimension if the brake pedal is left of the centerline of driver. If the clutch is forward of the brake, the sae j1100 is negative. For heavy-duty trucks, suspension seats will be positioned as specified by the vehicle manufacturer in sae j1100 normal driving position with sse fore and sae j1100 isolator locked out. If no arm is provided at the designated “X” plane, use a height of 1 80 mm above the SgRP.

H Rear opening height 8. Criminal penalties may sae j1100 for noncompliance. Rearmost-Highest Design H-Point— The rearmost ‘location of the full up position of vertical travel independent of track rise.

TOP Related  S2055N EBOOK

This measurement accounts for adjustments independent of track rise. Establishes the rearmost normal design driving or riding position of each designated seating position which sae j1100 consideration of all modes of adjustment, horizontal, vertical, and tilt, in a vehicle, b.

Pieces from subsequent Standard Luggage Sets may be used when the previous set is placed in the Luggage Compartment. Full text of ” SAE Wae General— The dimensions in this report will enable the sae j1100 of a vehicle as designed.

L55 Fiducial mark no. H26 Interior body height – front at zero Y plane 6. The limiting structural component shall be designated.

Full text of “SAE J Motor Vehicle Dimensions”

The forward limit is the rear side of the second seatback or the folded third seat. Is the reference point employed to position the two-dimensional drafting template with the 95th percentile leg described in SAE J This measurement includes vertical adjustment independent of track travel. The dash panel is usually sae j1100 vertical extension of the toe panel. This dimension excludes wheelhouses, local protrusions, and local depressions or pockets.

See Figure sae j1100 G 2 0. Track sae j1100, when provided, is the amount the H-Point increases in height ssae forward movement due to an inclined seat track.

All other sae j1100 features, such as an adjustable steering wheel and adjustable seat height, a seatback that adjusts independently from the Seat Cushion, power 4-way or 6-way seats, etc. Simulates the position of the Pivot Center of the human torso and thigh, and d.

Sae j1100 invites your written comments and suggestions. They are included in an effort to harmonize world-wide vehicle dimensioning sae j1100 and to permit accurate comparison of domestic and off-shore vehicle dimensions.